Clik here to view.
Von: OlliW
ja, das ist nötig Leveln heisst dass der Controller versucht die Motoren so anzusteuern dass die Imu waagrecht wird, wenn das nicht passiert stellt der Controller richtiger weise fest „Mist, ich kann...
View ArticleVon: motianlun 1111
hi OlliW： thanks for share your effort, i want to contect with you and share my own effort. I do a lot work on foc motor control , i hope i can help you to improve you project, and i also have some...
View ArticleVon: Ibai
Hi OlliW, Congratulations for this project, you nailed it! I’m pretty excited now that I got my board and I’m ready for setting it up. I flashed the latest firmware on my v1.31 board, using the v090...
View ArticleVon: Darren
Hi Olli, do you know whether the firmware would run on an M0 at 48 MHz? Or does it need a more powerful MCU? Thank you.
View ArticleVon: Ibai
Hi again, I’m still trying to find the solution… FTDI drivers installed correctly, also checked with HTerm if there is data transmission–> OK Running your o323BGCTool I perform the „Flash Firmware“,...
View ArticleVon: Tammo
3 von den Motoren liegen bei mir Zuhause und das Storm32 kommt am Freitag. Dann kann ich dir mehr berichten, ich glaube ja aber ich sehe es ja am Wochenende… Mit freundlichen Grüßen
View ArticleVon: Eddy
Ciao a tutti. Sono italiano ed ho acquistato il 3 axis strom32 ma non riesco a farlo funzionare. io non me ne intendo di elettronica per cui non riesco ad andare avanti. Quando lo accendo i braccetti...
View ArticleVon: Eddy
Hallo an alle . Ich bin Italiener und ich schreibe und mit dem Ãœbersetzer . Ich kaufte das 3-Achsen strom32 aber ich kann es nicht funktionieren. Ich meine nicht, auch elektronische , warum ich nicht...
View ArticleVon: Tammo
Ja kann er und das bis jetzt sehr gut, mal sehen was es wirklich macht wenn der endgültige Aufbau dran ist und ich alle Einstellung verstanden haben, bis jetzt super begeistert. Aber eins kann ich...
View ArticleVon: Feliphe G. Galiza
Hi, I am trying to develop a Brushless Gimbal using the Tiva C TM4C123G microcontroller. For now I am stuck trying to figure out how to generate three PWM signals shifted by 120 degrees. Can someone...
View ArticleVon: Han
is the project STorM32 NT BGC open code, and if so, where and how can i get a code? I can pay to get the code as well, thank you
View ArticleVon: nico
ciao eddy …secondo me l’errore di base che fai e‘ che, siccome la gimbal la scheda sono gia‘ settati e calibrati di fabbrica, tu devi solo attendere diversi secondi che si inizializzi tutto il...
View ArticleVon: LARRY
hello Is it possible storm32 is inverted mode? ↓↓↓↓↓↓↓↓↓↓↓↓↓↓↓↓↓↓↓↓↓ https://www.instagram.com/p/BDLw6f_Mq1U
View ArticleVon: LARRY
hi Is there any option storm32 skip gyro calibration at startup option in the alexmos board? I wish for quick use.
View ArticleVon: Philippe Benjamin Rymann
DANKE DANKE DANKE an alle die diesen Gimbal möglich gemacht haben. Es ist ein fantastisches Produkt.
View ArticleVon: Nick
Holy Sh*t; I just setup a cheep 3 axis gimbal with this board running 0.90 and a Xiaomi Yi, only most basic tuning and no PID tuning. Took a video, hand holding the gimbal base and moving it around...
View ArticleVon: Ibai
Hi again, After months I am still struggling with the problem… I write here my problem from previous comment: „FTDI drivers installed correctly, also checked with HTerm if there is data...
View ArticleVon: Dave Mills
I have the exact same problem as Lbai. I have Flashed the firmware. The DOS window confirmed it had loaded all 45 pages successfully. The board LEDs started flashing again. The Gimbal does not start...
View Article